IVT SW 2000 Sine wave inverter 12 V 2000 W

The robust SW-2000 sine wave inverter reliably and precisely converts an input voltage of 12 V DC into a true sine wave AC voltage of 230 V/50 Hz. Independent of the public power grid, even highly sensitive consumers as well as consumers with increased starting current can be operated in a stable and absolutely trouble-free manner.

Details

• True sine wave AC voltage 230 V/50 Hz
• High peak output power 3000 W
• Galvanic isolation of input and output stage
• Extensive protection functions
• Power start function
• 2 output sockets
• E-approval
• Low power consumption
• Power controlled fans
• Compact and lightweight design
• Connection for remote switch

Technical Data
Input:

• Rated voltage 12 V
• Voltage range DC
• 11 - 15 V
• Rated input current
• 167 A
• Input current, max. 250 A
• Deep discharge protection voltage 10.5 V
• Deep discharge protection voltage, adjustable
• no
• Prewarning deep discharge protection switch-off 11.5 V
• Restart voltage 12.5 V
• Rated power consumption, no-load 15 W

Output:

• Output voltage AC (- 8 % / + 5 %)
• 225 V
• Frequency (± 1 %)
• 50 Hz
• Signal shape Sine
• Continuous output current 8.89 A
• Continuous output power
• 2000 VA
• Peak output power (max. 2 s) 3000 VA
• Power factor cos phi > 0.8
• Rated efficiency > 88

General:

• Input connection Connection terminal 2 x M8
• Output connection 1 x safety socket
• 1 x Euro socket
• Suitable for plug type F, C
• Output connection USB (type A)
• no
• Temperature range -25 °C to +60 °C
• Sleep function no
• Standby function
• no
• Galvanic isolation (input/output)
• yes
• Power start function yes
• E-approval yes
• Connection for remote switch yes
• Fan cooling yes

Microprocessor controlled electronics
Due to the microprocessor-controlled electronics, continuous monitoring and control of the most important operating parameters, such as input voltage and frequency, is fully automatic. This ensures the constant stability of the output voltage.

Continuous power 2000 W - peak output power 3000 W
Especially with consumers that require a high inrush current, the start does not always run smoothly. For this reason, the SW-2000 is designed to provide a continuous output power of 3000 W for a short time.
To determine the appropriate inverter, you need your total power requirement. This is the sum of the power (W or VA) of the individual loads. We recommend that you allow for a power reserve of 30 - 40 % upwards.

Power start function for loads with high inrush current
The SW inverter is also equipped with the power start function. Advantage: Consumers with a high inrush or starting current are activated several times in quick succession with the maximum output power of the inverter, thus facilitating reliable starting of powerful consumers.

E-approval: suitable for fixed installation in vehicles
The Sinus inverters meet the legal requirements of the ECE regulation and thus have the E-certification. They are suitable for fixed installation in all vehicles with road approval, whether passenger cars, commercial vehicles or other vehicles with 12 V on-board voltage

Galvanic isolation of input and output stage
Galvanic isolation: Thanks to galvanic isolation, there is no electrically conductive connection between the input and output circuits. Therefore, no additional personal protection device (FI or DI switch) is required even for commercial use when only one 230 V consumer is connected.

Extensive protection functions
SW series inverters operate absolutely reliably and safely even under the toughest conditions. As standard, they are protected against overload, short circuit and overheating. Impending deep discharge of the battery is indicated by optical prewarning (LED) and prevented by automatic shutdown.

Two output sockets
Plug type: F, C and C
The Sinus inverter is equipped with two output sockets as standard. A 230 V protective contact socket, suitable for plug types C (Euro plug) and F (Schuko plug), as well as a Euro socket (plug type C) are available for current draw.

Compact and robust design
Conventional inverters are often equipped with large ring transformers. As a result, these are heavy and unwieldy. In contrast, IVT microprocessor-controlled inverters operate digitally thanks to innovative technology: large, heavy components are eliminated and replaced by small and powerful components. The valuable inner workings of the inverter are protected by a sturdy housing. The SW series inverters can be used as a stand-alone unit or mounted on a wall.

Connection socket for remote on/off switch
An additional connection socket is available for connecting an external on/off switch. A suitable plug with open ends for soldering a switch is included in the scope of delivery.

Suitable connection cable sets
For a safe and trouble-free operation of the SW inverters we recommend the use of the original IVT connection cables. These are precisely matched to the respective inverter in terms of conductor cross-section and cable length. The high-quality workmanship of our connection cables guarantees a particularly long service life, even under high loads. The cable set is already pre-assembled with matching ring lugs and wire end ferrules for connection to the battery and the inverter. All original IVT connection cables are supplied including fuse holder and 200 A fuse.

Power controlled fans
The power controlled fans minimize the noise of the inverter by switching them on only when needed.

Scope of delivery
Sine wave inverter SW-2000, 12 V Operating instructions DE, EN, FR, NL